Leather chopper mitt build along

For all the things we make ourselves for the outdoor world that are not covered in the other specific DIY area.
Message
Author
Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Leather chopper mitt build along

#1 Post by Ron Kulas »

My late great Uncle Al used to make leather chopper mitts and bring them up north when he would visit. We got a lot of use out of those mitts in cold weather. Here is one of those mitts Al made about 30 years ago.

Image

Al’s mitts were warm and simple and utilitarian and kept my hands warm while hunting all these years. For many years I have wanted to make my own mitts. The recent cold snap and the increase in my sewing projects got me again interested in trying my hand at sewing my own mitts. If there was anything I would change about Al’s mitts it would be the length and the liners. They didn’t go up the arm enough to cover the cuff of a jacket. I plan to make mine a bit longer and plan to have mine be skin side out (rather than the suede side out like Al’s). Also Al’s mitts did not have a removable liner. The faux fur he used was sewn into the leather mitt. I plan to make my liners removable so if the liners need drying the liner can be removed to speed drying and to be able to care for the liner separately from the leather since leather doesn’t like the heat I would use to dry the liner.

Then when I use the snow blower I wont have cold wrists and forearms. the longer cuff will make them warmer for hunting and ice fishing as well.

I will be using the tanned hide of a deer I killed a few years ago.

Image

As well as fur

Image

The liners will be a dual layer of Polartec fleece closest to the skin as well as wool. The wool comes from a Swiss army surplus blanket.

Image

Before I could any further I needed to make a pattern for the liner and another pattern for the leather mitt. Because I want a longer mitt that fits over the bulky sleeve of a winter jacket I had flare out the longer cuff. I will start with the fleece and wool liner and then make a mitt that fits over the liner. Here is the pattern I came up with. Its 3 pieces with a folding thumb.

Image

Then I cut the pieces from the wool and Polartec fleece.

Image

The two materials are sewn together to keep them from shifting when I join the separate pieces together.

Image

I plan to have fur on both the liner and the leather mitt. Its more for show than warmth.

Image

Before I can sew the fur to the other part of the liner I need to join the two pieces together to form the thumb. The three pictures below show the steps to form the thumb.

Image

Then fur is added to the other half of the liner.

Image

Then the two halves are sewn together.

Image

Should the outside leather get wet all the way through (I’m working to make sure that won’t happen) The wool outside of the liners is given a spray coating of silicone waterproofer.

Image

With the liners finished its time to make the leather outer mitt. Again I need a pattern. The leather mitt thumb will be a bit different than the thumb in the liner. This will be a bit more difficult to sew but will look far better.

Image

I made a practice thumb to get a feel for sewing it and for a size check. I’m glad I did at the thumb was a bit long so I shortened the pattern (since it was easier than growing my thumb)

Image

Then I cut the halves of the mitt from the deer skin.

Image

The plain deer skin is very light in color and will show dirt and stains pretty easy so I am going to stain the thumb and palm side with a mixture of brown and Ox blood with a little alcohol to thin it out since I don’t want a solid color. Once I oil the leather it will darken considerable from this shade. I have other plans for the back of the hand so Im not staining it.

While I wait for the stain to dry on the leather I have time to embellish the back of the mitt. I sewed on a strip of the same fur and added the Edge protection since the leather edge will curl and wrinkle over time if it not sewn.

Image

Then I saw the cuff as a big blank space needing something to fill it in so I reached for the sharpie marker.

Image

With the dyed leather dry its time to start sewing. I start by sewing the thumb inside out to hide the stitching and to protect it from wear.

Image

Then the thumb is turned right side out and slipped inside the opening in the palm and sewn from the outside. I stitched it twice for added strength.

Image

The two halves are sewn together inside out again to hind and protect the stitching and to tuck in the fur trim edge.

Image

Then the mitt is turned right side out. As you can see the palm was also a blank slate in need of some decoration so I fired up the sharpie marker again.

Image

The liner and the mitt meet for the first time. Everything fits.

Image

Waterproofing the leather is a two step process. It starts with neatsfoot oil. You can see from the sample piece of leather both the stained and natural leather will darken with the oil.

Image

The first oiling makes it dark. Another oiling will make it darker and so will a coating of mink oil.

Image

The mink oil is a paste or cream that looks a bit like Vaseline. I rub it in with a stiff sponge and then use a hot blow dryer to melt it so it soaks into the leather. The finished pair.

Image

My happy hand model braved the single digit temps for this photo shoot. Her bulky winter jacket sleeves fit nicely into the cuff of the mitt.

Image

For never having made chopper mitts before I am pleased with how they turned out and have plans on how to improve upon the next one. Here is a short video of the mitt being placed under running water. It shows the waterproofing of the neatsfoot and mink oil. Over time another coating of the mink oil will need to be added if the leather shows signs that its getting wet..

http://www.youtube.com/watch?v=pAxDjBn-cHg

My hand model has already put in a request for a pair for herself. She want different colors and symbols on hers.
The Joy is in the doing.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#2 Post by Ron Kulas »

My wife (mitten model) wanted her own pair of deer skin leather chopper mitts but she was not partial to bears or brown leather so I told her to pick out exactly what she wanted for her pair. She wanted bright blue leather and white fur and butterflies with white trim. The liner would be the same black blizzard fleece I have been using on other projects.

Image

Dying a tanned leather deer hide is a crap shoot in terms of what the final color will be. Here is the tanned leather before dying.

Image

I used Rit dye and white vinegar. The vinegar was added after the hide was in the dye for 5 minutes.

Image

I presoaked the leather in hot water for 15 minutes before dying.

Image

I soaked the leather in the dye for 30 minutes then rinsed it under hot water and then cold water.

Image

Then I stretched the hide out on a sheet of plywood and used a box fan to dry it.

Image

Once dry I had to find areas of the hide that were not streaky or blotchy to cut the pieces of the gloves from.

Image

Image

The back side of the mittens got white trim, white fur and the butterfly.

Image

Image

The palm side only gets white trim and the thumb sewn on. Im getting better at sewing the thumb to the palm.

Image

The liners are a double layer of fleece and long white fur.

Image

The finished mittens. The blue really worked out well. I thought it would end up dark but its nice and bright. I sprayed them with silicone waterproofer to keep them clean and dry.

Image

Image
The Joy is in the doing.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#3 Post by Ron Kulas »

Since I am having fun making these leather mittens I’ll keep going and make some and donate them to Wisconsin Bowhunters Assoc and Wisconsin Traditional Archers for their upcoming annual conventions. Both WBH and WTA sent me their embroidered emblems/patches to use in the creation of the mitts.

Since the WTA event is less than a month away I will get started on theirs first. For these mitts I am using nice dark suede cow hide I picked up from Tandy leather.

Image

Aside from the WTA patches I will be adding grey fur to both the leather mitt and the liner. The patch and fur will be on the back side of the mit but I want to add some decoration to the palm side so I went back to my supply of tanned deer hides and will sew the deer skin to the palm with the grain side out. The deer skin is much lighter so I will give it a light buckskin stain and sketch on some artwork. Each mit will have a different image.

The right mitt will have a bowhunter at full draw. Here is the image lightly penciled onto the deer skin.

Image

I follow that up with a fine tip sharpie permanent marker and after staining the leather.

Image

The left hand is going to have a scene with a buck standing with some trees in the background. While it could be viewed either way the buck is looking away from the screen not towards the screen. You are looking at the back of his neck as he faces away. When the two mits are worn palms side up it will create a scene in which the bowhunter is at draw on a quartering away buck. (that’s the thought anyway. Sometimes I think to hard about this stuff.)

Image

Image

After the thumb is sewn to the palm I add the buckskin with the artwork to the palm.

Image

Here are the mitts before I join the two halves together.

Image

Image

After the two halves are sewn together and trimmed and turned right side out, I sprayed them with a heavy coat of Atsco silicone waterproofer to make sure they keep the user dry and to set the inked image in place. The waterproofer darken the leather just a bit.

Image

Image

The mitts need warm fleece liners. I used a double layer of blizzard fleece and grey fur.

Image

The finished WTA mitts.

Image

Image

The WBH mitts. The bowhunter on this mitt was my own creation. The deer image I found on the web. The WBH and arrowhead was also my own design.


Image

Image

Image

Image

Image
The Joy is in the doing.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#4 Post by Ron Kulas »

I just finished an art piece for a donation to WTA for their fund raiser to go with the mittens. When I finish the WBH mitts I will make a like piece for WBH. This is tanned deer hide stretched with sinew on a oak framework. It measures 12 by 14

Image

Image

The WBH mittens and wall art are finished.

Image

Image

Image
The Joy is in the doing.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#5 Post by Ron Kulas »

Ive improved my pattern and completed a pair for a member of our archery club.. This style has a little longer cuff and is more fitted to the wrist.

He supplied me with a tanned deer hide for the project. It was in a package for a very long time and had lots of creases so I soaked it in warm water for a couple hours.

Image

Then stretched and dried.

Image

Then construction began

Image

Image

Image

This is the design he asked to be inked into the leather.

Image
The Joy is in the doing.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#6 Post by Ron Kulas »

I was asked to make a pair of leather Chopper mittens for a UW Wisconsin Badger fan. I will make these a two tone design using split cowhide suede for the palms and cow leather tanned to look like buckskin for the backs. The removable liners will be fleece with a Wisconsin Badger pattern.. Here is the starting point.

Image

Leather parts cut out and ready for red trim.

Image

The buckskin cow hide lends itself well to adding ink. Bucky badger added.

Image

All the leather and trim and ink complete.

Image

Image

Then a deep soaking with a silicone waterproofer and set aide to dry while I work on the fleece liners. It darkens the leather but once dried goes back to its original color.

Image

To make sure these mittens are warm I doubled up the fleece. Here are the pieces before sewing.

Image

In progress.

Image

The finished fleece liners with trim added.

Image

Image

The liners in the mittens.

Image

My hand model wearing the finished product.

Image

They get a personalized label. (not the they will be confused with another pair since these are a one-of-a-kind set.)

Image
The Joy is in the doing.

Captainkirk
Site Admin
Posts: 12787
Joined: Tue Aug 26, 2014 8:19 pm

Re: Leather chopper mitt build along

#7 Post by Captainkirk »

This is amazing!
If you would have asked me an hour ago I would've said sewing was for girls and sissies. But that is too cool!
Once again I am blown away, Ron! Thanks for sharing!
Aim small, miss small!

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#8 Post by Ron Kulas »

I do a lot of sewing. Im working on leather mittens right now. I sew a lot of hunting gear. That way I get what I want. I have a lot of sewing projects to share.
The Joy is in the doing.

Carpdaddy
Site Admin
Posts: 9469
Joined: Tue Dec 31, 2013 7:36 pm

Re: Leather chopper mitt build along

#9 Post by Carpdaddy »

As Red Green says; "If the women don't find you handsome, they better find you handy"! Your a handy feller, don't know about the other part. Nice work.

Ron Kulas
Posts: 657
Joined: Wed Oct 21, 2015 8:33 am

Re: Leather chopper mitt build along

#10 Post by Ron Kulas »

Im like a male model. I look that good.
The Joy is in the doing.

Post Reply

Return to “DIY section”